Frame Scaffolding Rental in NYC, Set Up and Taken Down by One Crew

Prefabricated steel frames, with cross braces between each pair, stack up along flat facades and low-rise buildings. Our crew assembles and dismantles them in all five boroughs.

Since 2007

$2M general liability

OSHA-trained crews

All five boroughs

Inside a frame scaffold

Frame scaffolding is a supported scaffold whose sections arrive as welded steel frames. The crew stands two frames side by side, locks them square with cross braces and lays planks across the bay. Coupling pins stack the next frames on top.

Frames and braces

Part What it does
Welded frames The end sections, each with two legs and rungs between them
Cross braces Diagonal pairs that hold two frames square
Coupling pins Join each frame to the one above it
Base plates and screw jacks Feet that level the scaffold on uneven ground
Planks The deck at each working level
Guardrails and toe boards Edge protection along each level
Ties Anchor the frames to the wall at intervals

Common frame types

Walk-through frames have an open arch at the base, so workers and materials can pass between the legs. Mason frames stand shorter, with rungs closer together, and masons often stage brick and block from them. Your quote names the frames we’d use.

Buildings and jobs that call for frames

We usually suggest frames when the wall runs flat and the building stays low.

Flat, regular facades

Frames go up quickly on a facade with no setbacks or deep projections. Rows of flat-front apartment buildings in Queens and the Bronx are typical frame jobs.

Houses and small residential buildings

A residential scaffold for a one- or two-family house is often a frame job. Painting, siding, window replacement and repointing on a brownstone or a small walk-up usually run from frames.

Paired with a sidewalk shed

Some jobs also need overhead protection for people on the sidewalk. We can put up the frames and a sidewalk shed on the same schedule. 

Not sure frames fit your building? Send the address and a photo of the facade, and we’ll recommend the system.

When to skip frames

Frames come in fixed sizes, so they struggle on a building that steps back, carries deep cornices or bulges out in bays. Jobs where the scaffold has to begin above a shed often go the same way. For those jobs we usually suggest pipe scaffolding, which the crew shapes to the building one joint at a time. That page compares the two systems side by side. For facade work high on a tower, a swing stage that hangs from the roof may fit better than either.

Looking at other systems? Our scaffolding rental page covers them.

Est. 2007

NYC permit and design rules for frame scaffolds

DOB treats a frame scaffold as a supported scaffold, the same category as pipe. The 40-foot line matters here, because many frame jobs on houses and low-rise buildings stay under it.

When you need a DOB permit

Once the frames reach 40 feet, DOB wants a permit before they go up. Frames that sit on a sidewalk shed add the shed’s height to that count. Filing happens in DOB NOW: Build.

Shorter frames stay permit-free only when they pass all six tests in BC 3314.2. The tests cover height, scaffold type, hoisting equipment, load, bracket use and restraint against tipping.

When an engineer designs it

BC 3314.3.1 hands supported scaffold design to a registered design professional, so an engineer or architect draws the plans. Frames can skip that design only if they meet BC 3314.3.1’s own list of exceptions, which isn’t the same as the permit list. So a frame job can be permit-free and still need an engineer’s design. The code counts the permit and the design as two separate checks.

How your frame job runs

01

Quote and site check

We look at the facade, the ground under the frames and how close the neighbors sit. Your quote names the frame type, the elevations we’ll scaffold and the rental period.

02

Setup

The crew levels the base with screw jacks, stands the first frames and braces them before going higher. They tie the scaffold to the wall level by level.

03

While the work is under way

If a level needs to move, call the same team. They’ll make the change within the scaffold’s design limits.

03

Taking it down

When the work ends, that same team takes the frames apart, top level first, and clears the site.

Questions about frame scaffolds

Questions

Working on a house with neighbors close on both sides? Call (929) 837-3852, and we’ll plan the setup around them.

How do the frames go together?

Pairs of welded steel frames stand side by side, with cross braces holding each pair square. Coupling pins join the next frames above, and planks make the deck at each level. Screw jacks or base plates carry the bottom frames.

Yes. That puts it under DOB’s 40-foot permit rule, and a shed under the frames adds its height to the total. The design rule in BC 3314.3.1 applies too, unless the scaffold meets that section’s exceptions.

Often, yes. Houses, brownstones and small walk-ups usually have the flat, low facades frames handle well. We confirm the fit in your quote.

When the facade has setbacks, heavy cornices or bays, or the scaffold has to start on top of a shed. Our pipe scaffolding service compares both systems.

Start with the address and how many stories the building has. Add the sides that need frames, your start date and any plans for a sidewalk shed.

Show us the building

Share the address, the number of stories and, if you have one, a picture of the front. Hitech Scaffolding & Sidewalk Shed has worked on NYC buildings since 2007, with $2M in general liability coverage. Every installer on our crew has OSHA training. Our all services page covers sheds, fencing and barriers too.